MGB GT gets an FIA rated ATL Fuel Cell

At the LeMons 2013 Capitol Offense race, we were politely told to fix the ass end of the car, as described in our race report.

What we did...

FUEL CELL INSTALL OVERVIEW

Specifications:

• ATL 15 gallon FIA rated LeMons Legal fuel cell, direct off the Lemons web site in order to guarantee this cell is acceptable. 
• Mounted in the OEM gas tank location (a little higher so we don't drag on bad entries to The Karussell!)
• Using professional Speedway Motors Fuel Cell Bracket mount bolted to the frame
• We have the OEM back bumper and an additional internal bumper (built from old roll cage material) behind the cell to help in heavier fender benders
• No splash bulkhead required (though we may add one later)

The fuel cell install has begun!

Here's some pics, not done yet but here it is so far:

Where the mount meets the car; long horizontals (marked '1 inch steel' here) were cut to 38 inches so they overlap the upper frame for mounting. The section of roll bar you see was existing, and has a vertical piece (inside, between two frames) about 2 inches high that welds it to the lower frame.

ATL Fuel Cell in an MGB GT hatchback

The horizontal side pieces are used from Speedway unmolested, however the verticals were cut down to 8 inches and re-drilled (oddly, one of the eight holes was the wrong size from the factory):

ATL Fuel Cell in an MGB GT hatchback - side traps

 

 

Here is the first fitting, without the improved fuel cell cage frame pieces. We could not move it forward any further without hitting the differential! It's in the OEM position, so will be OK. Well, we could move it forward, but it would be sitting on the drivers shoulders... and that's just ridiculous since we already have a cool-shirt system.

ATL Fuel Cell in an MGB GT hatchback - snugly in place

Here is the original frame from Speedway Motors; note the two upper short horizontal bars (outermost) are held in place by magnets in this picture; we were fitting the fuel cell and moving those pieces around. The holes to mount those pieces permanently have not been drilled yet, we are waiting to finish the extra L-Channel trap frame before doing so, in order to ensure a nice tight fit.

Here are the pieces of the L-Channel trap frame (I don't know the proper name for it, but it is made of L Channel steel and it traps the bottom of the fuel cell, so that's what I am calling it). We made pieces to go around all the edges on the bottom and then up the sides on the corners. Measurements in inches are 24 5/8 (two), 18 1/4 (two), 9 1/4 (four). The vertical corner pieces do not hit the upper flange, we did not want that to be a stress point.

Here is the cage tack welded, before complete joint welding by pro:

The Speedway Motors Fuel Cell Cage - augmented with angle iron to protect edges, tack welded, prior to full weld.

Update 2013-08-06 - Cage back from the welder!

Painted, mounted:

Fuel cell cage, resting in well; about 6 inches higher than normal MGB gas tank and a bit more forward

Looks simple, doesn't it?



That vent line is just a place holder



MGB Fuel Cell corner with Grade 8 mounting hardware

Detail, underneath: corner protection evident, note cross bar bolted and welded! pffft

In situ; pay no attention to that missing vent line....

Front the top

Update 2013-08-07 - some extra pics for the curious

 

(more pics to come, as we endeavor to make NJMP!!!)

REFERENCES:

Some links to 24 Hours of LeMons Forums regarding Fuel Cells:

• New Fuel cell rules for 2013 - Teams with fuel cells please read
• Show us your fuel cell install
• School me on fuel cells
• Fuel cells, bulkheads, and hatchbacks
• ATL fuel cell and hatch back
• Fuel cell vent tube
• Example of bad install here: I think a stupid cage question
• 280Z Fuel Cell Install - Vent/Cage/Mount - Check Our Work Please!
• A LeMons team on facebook - fuel cell install 
• What is everyone using for a fuel cell
• YouTube video: ATL Fuel Cell Install by Car and Driver Magazine for 24 Hours of LeMons
• Will this fuel cell install pass tech?
• Completed our fuel cell install Need clarification on bulkhead rule

Shopping List:

• ATL 15 gallon FIA rated LeMons Legal fuel cell, direct off the Lemons web site
• Speedway Motors Fuel Cell Bracket - says it fits 16 gallon cells but really fits 16 gal Speedway cells; 25” long x 19” wide x 11” tall

Fuel Cell Rules & Notes from 24 Hours of LeMons site:

• Common Tech Failures:  Fuel cells.  If the cell is not an FIA certified rubber bladder cell (Fuel Safe or ATL) then it must have a sealed metal barrier between it and the driver, even if it is in a metal can.  NO EXCEPTIONS!      This means most cells from Jazz, RCI, Summit, Etc.   They all need a metal bulk head between the cell and the driver.   A fuel cell install is always judged by its quality of install and is looked at by the race manager, The bar is high, do a good job.   
• How NOT to Fail LeMons Safety Inspections: Cell can't be too low (punctures), too high (rollovers), and must be far enough away from edges to avoid damage during typical accidents.
• Rulebook: (note: always check most up to date rulebook!) - 3.25: Fuel Tanks/Fuel Cells: All fuel systems, including OE fuel tanks and aftermarket fuel cells, must be sound and in good working order. Maximum allowed capacity is 24 gallons or less. Fuel tanks or cells must be completely behind, or completely in front of, the driver (unless OE parts in their OE locations). No second fuel tanks allowed (unless OE parts in their OE locations).
          3.25.1: Aftermarket Fuel Cells Versus OE Fuel Tanks. Fuel cells are allowed,but they are NOT mandatory. Don't make the rookie mistake of assuming that anything billed as a "fuel cell" is safer than a sound OE fuel tank.High-quality, professionally constructed, correctly installed fuel cells tend to be safer than OE tanks; cheap and/or poorly installed fuel cells tend to be less safe than OE tanks.
          3.25.2: Fuel Cell Installation: If you decide to install a fuel cell, it must be securely mounted in a professional manner and must be installed in a safe location where it won't be damaged in an impact or drag on the ground if the car leaves the track. All aftermarket fuel components must use threaded fittings and appropriate hose types, and must include all appropriate racecar-quality vents, valves, and other safety features. Fuel-cell installations will be judged on their overall execution and apparent safety. Cars whose fuel cells do not feature internal foam, a puncture-resistant bladder, and/or metal encasement are considerably more likely to fail tech inspection.
  Also this section spells out an FIA certified fuel cell if it is going to be sharing the passenger compartment with the driver (or in the rear hatch area in a hatchback)
  3.18: Fuel Bulkhead: The fuel-tank area must be totally separated from the driving compartment. For example, if the fuel tank is in the trunk area, any openings between the trunk and the cockpit must be permanently sealed with bolted, riveted, or welded metal panels. OE fuel tanks that are separate from, and located completely below, the trunk floor or rear-cabin floor are acceptable. If the fuel tank can't be completely separated from the cockpit by metal panels, a metal-encased, FIA-certified fuel cell with all related compliant fittings must be used.

Race Report: 2013 Capitol Offense - The 24 Hours of LeMons

Not. We failed tech.

On our home track.

On the most-fun-per-mile track on the east coast.

On a gorgeous weekend.

What did it? A perfect storm of:

• Old Fuel Cell (RCI, not FAI rated) and 
• Rear fuel cell protecting roll cage that tied into the front roll cage (a no-no for 2013 that we somehow missed in the rule updates, and the safety tech judge at Monticello either missed or let slide and didn't mention) AND also 
• Diagonals of rear roll cage tied from the main upper hoop to behind the rear axle (another no-no, for 2012 that we somehow missed in the rule updates, and the safety tech judge at the last 4 races either missed or let slide and didn't mention). 

We couldn't just cut out the offending sections because they were holding in the fuel cell. Another team graciously offered to stay up all night to help fix it, but as they had 2 of their own cars needing work we didn't feel comfortable leaning on them so heavily. Death before Dishonor! Still, this hurt, being our favorite track and our home track.


MGB GT Race Car : Friday Practice Session in style!

We did have some mechanical issues Friday at test day; burnt a half quart of oil driving to the track (rings? uh oh), and the accelerator cable was very hard and making grinding noises. We also could not get above 4500 RPM (redline is at 5500 RPM), which renders the weak car even weaker, to the point of idling around the track - no fun for anyone. We checked the pedal linkage (since it came off last year at Summit), adjusted the carb linkage, greased the heck out of it, and did not find the solution by the time Safety Tech came around, at which point it was moot (though it did play a role in making us decide to not stay up all night gerry rigging an unsafe roll cage fix to get past tech).


Inconsequential Drama Recap:

Lesson 1: Do not go to Pep Boys for your tires, and if you do, (1) do it well ahead of time, (2) make sure the tires you order are not discontinued, (3) make sure the team mate ordering them knows "200 treadwear" is the top priority, (4) make sure the placement of the wheel weights do not chew away your tie rod bellows, and (5) don't go to Pep Boys. We did finally get them. See: photographic proof:


All 4, we counted

Wheel weights on inner rim interfering with tie rod bellows, move and Gorilla Tape elsewhere!

Lesson 2: Be Excessive. It's best to clean out Perty Ada The Short Bus to Adventure Tow Vehicle and Pit Party House with a Roomba and a 140 MPH leaf blower:

Friggin stink bugs from hell, begone!

Lesson 3: Bring chalk. Other than that, there may be no fix for this one. LeMons said no entry Thursday night, but we had an old friend that lived nearby walk over to the main gate and he said teams were setting up and Summit Point Gate said "go on in!". So, I threw everything I could into Perty Ada The Short Bus to Adventure and drove up to Summit; the front gate said "go on in" but when I got to the bridge at Shenandoah they had just tied it off, the LeMons judges saying Summit messed up and let some teams in. But she felt bad for me (I enacted Lesson #2 and was excessively polite) and she suggested that I could, once they left, hand carry all my spare tires and big crap a mile down to the pits and  mark off 3 pit spots (I was also saving spots for our Sister teams Team Judge Phil and Ruby McQueen (aka ex the DRTy e30s). So I did, damn the Hiatal Hernia (that has knocked me out of 2 other races), luckily I had grabbed some of my kids Sidewalk Chalk and a tape measure (Judge said 20 foot spots, any more and penalties would be levied) used it to mark off spaces. I ran out of chalk, but at least had enough to mark them some:

Midnight at Summit Point 24 Hours of LeMons Pit Land Grab and Cluster Fark

The punch line being that by the time we left Thursday late at night, the Summit Point Security guard told me it was stupid to hand carry that stuff, and that he had to drive through the gate tape anyway do his rounds 3 times and hour. >:(  But, as I had given my word to the LeMons judge, I left the school bus at the gate and moved it in the morning. Whatever, it's all good.

Lesson 4: Do not be last in line for Tech Inspection. After 8 hours in the sun listening to spoiled race car people whine, the judges may be a bit grumpy. Get 'em while they're fresh & happy.



Windshield wipers... well maybe not

Removed the plexiglass windshield (eg scratch collector) that we had so much trouble with (eg couldn't see through) in the rain at Charlotte Motor Speedway last year (eg Black Flagged for passing under Yellow that we couldn't see).

Drilled out the rivets and removed the remaining screws (eg 25% of the screws have been lost to vibration over time). While it was out I stripped down any surface rust (eg it's English) and coated them with De-Ruster treatment.

You can see the red Kill Switch that I will be moving to the center of the dash (as per ChumpCar Rules [.pdf]) while the windshield is still out.

The big item that was planned to do while the windshield was out: adding some Windshield Wipers! I had scavenged a system from Crazy Rays last fall and had been waiting impatiently to install them.

Finally get to it and.... can't be done as is.

The roll bar, eg the excessively over-engineered roll bar, is in the way. The photo to the left is a shot from inside the car looking forward. The farthest blue bar is completely unnecessary for LeMons, ChumpCar, and probably VRG, SCCA, NASA, and pretty much anything else except a Sherman Tank Demolition Derby. Never-the-less, I can't bring myself to remove the extra pieces; after all I've hoodwinked talked my friends & family into racing this beastie and therefore the more safety qualified the car is the better. Who cares if it doubles the weight of the car?

Sigh.

So, options at this point seem to be:

1. Cut out extra roll bar bits (don't wanna!)
2. Install some other after market wipers, possibly a single one on driver side only
3. Install the MGB wipers, but from above the windshield! Top rollbar may be in the way :-(
4. Drive without wipers; since we now have a GLASS windshield we can use Rain-X and it may be ok. :-(
5. Do a 1968 American Rambler wiper system eg twine and clothes hangers manually operated
6. Rig up a few hairdryers on the hood pointed at the windshield (this is LeMons after all)
7. Hire a Baltimore street corner window wash guy to sit on hood during race
8. <Your suggestion here; please leave comment below.>

Fuel Cell Quarantine

Since the Fuel Cell doesn't have a FAI stickier on it (even though the company makes the same cells for another company which is FAI listed), I decided to play it safe and quarantine the tank as per LeMons rules. So, all holes between tank and driver compartment must be sealed.

I had a blast making this; heaven knows why - it was a real pain.

This took the better part of 2 days, and I don't have to door done yet - but you get the idea:

That's the fuel cell at the bottom that the scissors are sitting on


Underside of 2nd half of trunk lid, made with a galvanized steel shelf and parts from a sliding door track:



The not-quite finished trunk lid assembly. All rivets making it one piece, sheet metal screws holding it to the frame members. The screws are LONG so if they ever come loose, we'll see them long before they escape. Kira helped on the painting.

2013 UPDATE!

MGB GT gets an FIA rated ATL Fuel Cell